A thermal camera shows me temperature differences on the surface of a wall, ceiling or floor. That’s how I find wet drywall, missing insulation, AC registers that aren’t cooling and electrical parts running hot, none of which you can see with your eyes. What it can’t do is look through the wall, prove a cool spot is water, or catch a leak that hasn’t started yet.
So it’s a great tool. It’s not X-ray vision. Here’s what it actually finds in Arizona homes, where it falls short, and what to do when your report has a thermal image in it.
What a thermal camera actually sees
The camera reads heat coming off a surface and turns it into a picture. Warm shows up one color, cool shows up another. That’s it. InterNACHI’s guide for inspectors puts it simply: “Thermal images show surface-heat variations.” The camera doesn’t know why a spot is cooler. It just tells me where to look.
Water is the big one. Wet drywall cools off as the water evaporates, so a wet spot reads cooler than the dry wall around it. InterNACHI’s moisture guide explains that wet areas show up as dark areas in the thermal image, and the camera is picking up the temperature difference, not the water itself.
Arizona actually helps here. The camera works best when there’s a big temperature difference between inside and outside. InterNACHI’s guide to inspecting for air leaks with IR cameras calls a 15 to 20 degree difference ideal, and says the peak of the cooling season is a good time to scan because the air conditioning can be run to widen the gap. On a summer afternoon in the Valley, with the sun on the stucco and the AC holding the house cool, problems jump right out on the screen.
What it finds in Arizona homes
These are the things I use the camera for on almost every house:
- Wet drywall and ceilings. Under bathrooms, around tubs and showers, below upstairs sinks, and on garage ceilings under a second-floor bathroom. On a 1997 Glendale home, the camera confirmed active leaks from an upstairs bathroom that were already showing in the garage ceiling below.
- Missing insulation. Warm patches on the ceiling where the insulation has been pushed aside or was never installed. InterNACHI notes these hot and cold spots can point to missing or inadequate insulation, which then gets checked up close.
- AC registers that aren’t cooling. I run the air conditioning and scan every register. On a rebuilt 1969 house, most registers were putting out 57 to 61 degree air, but a handful in the hallway and a bedroom were at 80 to 85. That points to a duct problem in the attic.
- Hot electrical parts. Breakers, wires and outlets that are running warmer than everything around them. Heat in electrical is a fire chain, so that one goes straight to an electrician.
- Roof leaks. A roof leak that has soaked the ceiling shows up the same way wet drywall does, so I scan the ceilings closely, especially after a monsoon storm.
What it can’t do
This is where people get the wrong idea. A thermal camera is a lead, not a verdict.
- It can’t see through walls. It reads the surface. If a pipe is dripping inside the wall cavity but the drywall hasn’t cooled off yet, there may be nothing to see.
- A cool spot isn’t always water. It can be missing insulation, an AC register nearby, or a draft. That’s why I don’t write “leak” off the camera alone.
- Shiny surfaces fool it. InterNACHI warns that reflective surfaces can pick up heat from something else in the room, like “a hot light bulb elsewhere in the room.” Tile, glass and metal need a second look from another angle.
- It shows today, not next week. If a fitting is fine during the inspection and starts dripping three days later, no camera is going to catch that ahead of time.
- It can’t see what I can’t reach. On that rebuilt 1969 house, the builder never put in an attic access. The camera told me several ducts weren’t cooling, but with no way into the attic I couldn’t see why.
A leak that showed up after the inspection
The video above is a good example of that last point. I inspected a vacant house in San Tan Valley, and a few days later my client called and said the toilet in the bathroom was leaking. So I drove back out, got the door opened through the showing service, and found water all the way around the base of the toilet, actively dripping.
Here’s the catch. The leak wasn’t at the shutoff valve itself. It was at the compression fitting on the back side of the angle stop, where the copper pipe connects. So turning the angle stop off did nothing, because the water was getting out before it ever reached the valve. I had to shut off the main water to the house and drain the toilet tank to stop it.
The report had already called out peeling paint and water lines in that spot, so this wasn’t a brand-new leak. But it wasn’t that visible on inspection day. Sitting vacant, with water in the lines and nobody checking, it got a lot worse in a few days. Left alone, water like that gets under the flooring and starts warping it up.
The good news: it’s not the end of the world. A new angle stop on a compression fitting is not a difficult fix. A handyman or a plumber can do it. The lesson is that a thermal scan, a moisture reading or any inspection is a snapshot of one day. Your final walkthrough matters, and so does calling your inspector if something changes.
How I confirm what the camera shows
When the camera shows me a cool spot, I put a moisture meter on it before it goes in the report. InterNACHI’s guidance is the same: “thermal imaging should be used in conjunction with a moisture meter.” The camera finds it fast. The meter tells me if it’s actually wet.
I also run water. Showers, tubs and sinks get used during the inspection, and then I scan the walls and ceilings around and below them. A drip that only happens when water is flowing won’t show up on a dry wall. Same thing with the AC: I let it run before I scan the registers, so I’m reading real airflow and not just a warm house.
For electrical, a hot spot at the panel gets written up for an electrician. The Electrical Safety Foundation lists electrical warning signs like warm outlets, a burning smell, discolored switches and lights that flicker or dim, and says to have a qualified electrician check the home. I’m not going to diagnose the circuit. I’m going to tell you it’s hot and who to call.
What to do if your report has a thermal finding
- Find the spot. The thermal images are in your report. Go look at that wall or ceiling yourself so you know exactly where it is.
- Wet area confirmed: get a licensed plumber out for an estimate to find the source. If it’s under a roof, call a roofer. If the area has been wet a long time, ask about air quality testing.
- Cooling problem at the registers: an HVAC tech for an estimate on the ductwork in the attic.
- Hot breaker or outlet: a licensed electrician, before you close.
- Put it on the BINSR. Leaks and electrical heat are the kind of items buyers ask the seller to address. Here’s how the BINSR works in Arizona.
- Check it again at the walkthrough. Look under sinks and around toilets, and look at the water meter with everything off. If something changed since the inspection, call me.
Thermal imaging inspections in Gilbert and across Arizona
I scan homes with a thermal camera as part of my residential home inspections, and you can read more about how it works on my thermal imaging inspection page. I inspect homes in San Tan Valley, Queen Creek and the rest of the Valley. Every home inspection includes a termite (WDO) inspection at no extra charge, plus a 1-year termite warranty through Firehouse Pest Control in Gilbert if no active termites are found.
Buying a home? Book your inspection online or call 623-399-0079.
Property Inspections Plus is a Gilbert, AZ home inspection company led by Certified Master Inspector Dan Pierce. We inspect homes across the East Valley, the Phoenix metro and the rest of Arizona. See all of our service areas.


